+86-20-86215789 service@adhesive-dy.com
English
| Quantity: | |
|---|---|
Product Advantage
Feature:
1.Advanced Mold-Resistant Formulation
Neutral cures,white and clear color,integrates powerful biocides that actively prevent the emergence and growth of black mold and mildew.
2.Long-Term Protection in Humid Conditions
Maintains its anti-fungal efficacy even in consistently damp and poorly ventilated areas.
3.Dense, Non-Porous Cured Surface
Creates a smooth, seamless finish that denies moisture and organic matter a place to accumulate.
4.Ideal for High-Risk Wet Areas
Specifically engineered for prolonged exposure to steam and water splashes in kitchens and bathrooms.
Technical Parameters
Test Items | Technical Indicators GB/T14683-2017 | Test Results | Remarks | ||
Appearance | Appearance:Fine uniform paste, no bubbles,no caking.No gel, no crust,no undispersed precipitates | Appearance:Fine uniform paste, no bubbles,no caking.No gel, no crust,no undispersed precipitates | Qualified | ||
Density/g/cm³ | ±0.1 | 1.5 | Qualified | ||
Surface Dry Time/h | ≤3 | 1 | Qualified | ||
Extrusion(ml/min) | ≥150 | 379 | Qualified | ||
Elastic Response Rate % | ≥80 | 94 | |||
Sag | ≤3 | 0 | Qualified | ||
Tensile Modulus（MPa) | 23℃ | ＞0.4 | 0.7 | Qualified | |
-20℃ | ＞0.6 | 0.7 | Qualified | ||
Fixed-stretch adhesion | Not deformed | Not deformed/60% | Qualified | ||
Determined adhesion after immersion in water | Not deformed | Not deformed/60% | Qualified | ||
Cold drawing - hot pressing after bonding | Not deformed
| Not deformed
| Qualified | ||
Adhesion after UV radiation | Not deformed | Not deformed/60% | Qualified | ||
Mass loss rate | ≤8 | 4.4 | Qualified | ||
Conclusion | The batch of products detected by the judge: （ ﹀ ）Qualified （ ）Unqualified | ||||
Product Uses
Applications:
Suitable for decorations in kitchens and bathrooms.
Bonding and sealing bathroom accessories, mirrors, baths, showers, basins ,sinks and sanitary ware to various substrates.
Use for advertising and home decorations and so on connecting joints for tiling, plumbing, air conditioning.
Product Operate Guide
Step 1: Make sure compatibility and adhesion between sealants and adhesive material before using.
Step 2: The sealant displays excellent adhesive effect in the clean environment with temperature of 4℃-40℃and Relative Humidity(RH)of40%-80%.
Step 3:Surface cleaning for bond substrates, clean up the dirt, grease and other contaminants, then affixedtemporary protective tape.
Step 4: According to the size you want, cut out sealant mouth.
Diameter of Gun nozzle should be smaller than the thickness ofthe sealant injection place, it makesnozzle can stretch into the 1/2 depth of the sealant injection place. Start to inject sealant whensubstrate surface is completely dry, Extrusion and injection of sealant shall be continuous ,whichmakes sure the extrusion of sealant is continuous and uniform cylinder, the move the gun slowly anduniformly, make sure the substrate interface is full of silicone sealant. Quick move is not allowed forthe gun, it will cases bubbles or holes.
Step 5: Decoration should be carried out when the injection is finished, and remove temporary protective tape.
1.Surface Cleaning
2.Affixed Tape
3.Sealant Mouth Cutting
4.Injection
5.Surface Fixing
6.Tape Remove
7.Finish
FAQ
